Search found 246 matches
- Sun Feb 05, 2012 2:56 pm
- Forum: Technical Articles
- Topic: Mainsheet traveller
- Replies: 9
- Views: 5158
Re: Mainsheet traveller
Re last post, this was the same reason I opened this discussion, also trying to make such a decision and wanted to see what others had done, thought. I'll be interested in further responses. Pics so far have been useful, thanks. I have been checking out traveller parts and still insure of what i sho...
- Sun Jan 29, 2012 4:48 pm
- Forum: General Discussion
- Topic: mainsheet traveller
- Replies: 3
- Views: 2624
mainsheet traveller
Hi All I would be interested in pictures and comments about modifications to the existing mainsheet traveller. I am thinking on adding a pulley-cleat system to make it easier to move the traveller during sailing manoeuvres. I recently have been experimenting with using the traveller to maintain spee...
- Wed Jan 25, 2012 6:05 pm
- Forum: Technical Articles
- Topic: Mast Compression Posts
- Replies: 7
- Views: 6216
Re: Mast Compression Posts
Hi again: Here's some more pics of the work I'm currently doing in my boat to shore up the strength of the inner arch/compression point under the mast. The pics show how I've now glued (using resin) the 5-ply 'lintel' in around the top of the arch, as well as fixed the two 'posts' on either side to...
- Wed Jan 25, 2012 6:00 pm
- Forum: Technical Articles
- Topic: Leaking bilge and centre-plate
- Replies: 27
- Views: 16820
Re: Leaking bilge and centre-plate
I have recently spoken with a shipwright here in Batemans Bay about my leaking bilge issue on my I563, he suggests cutting a small inspection hole above were the bolt is and then removing bolt and doing repairs with the yacht on the trailer, followed by a re-glass and sealing with epoxy. Can anyone ...
- Tue Nov 29, 2011 1:21 pm
- Forum: General Discussion
- Topic: Broken Vang Bracket
- Replies: 14
- Views: 8163
Re: Broken Vang Bracket
I called Bob Keeley today and chatted and ordered replacement mast base plate and insert. Not sure of final cost probably around $300. In the interim after also chatting with my local chandlery this morning and as a result of thier advice I mounted another connector to the mast for the vang. This pl...
- Mon Nov 28, 2011 4:17 pm
- Forum: General Discussion
- Topic: Broken Vang Bracket
- Replies: 14
- Views: 8163
Re: Broken Vang Bracket
Thanks everyone for the very useful feedback comments and the photo. Tardy in my responses as I have been in NZ for last few days. Ian that photo you posted helps enormously and confirms what I had also been considering as an option but unsure if it would work. I was convinced that I would be instal...
- Thu Nov 24, 2011 6:34 pm
- Forum: General Discussion
- Topic: Broken Vang Bracket
- Replies: 14
- Views: 8163
Re: Broken Vang Bracket
As you see just four tappers plus Sikaflex it feels very firm but....
- Thu Nov 24, 2011 4:51 pm
- Forum: General Discussion
- Topic: Broken Vang Bracket
- Replies: 14
- Views: 8163
Broken Vang Bracket
Last weekend the bracket at the base of the mast to which the Vang was attached via a U shackle snapped in a strong wind on a run. I post the picture below to show the replacement I have added to the mast base mound. Issue to me is that I thought this mound was solid fiberglass but when I drilled in...
- Thu Nov 03, 2011 6:07 pm
- Forum: Technical Articles
- Topic: Trailer bearing change
- Replies: 4
- Views: 2989
Re: Trailer bearing change
I have added a new grease cap which forms and additional level of seal and allows me to pump grease into the bearing i was advised about every 6 months, its spring loaded to when grease breaks down you add more until spring bounces back - note nice outer palstic seal also, these parts are all stainl...
- Thu Nov 03, 2011 6:02 pm
- Forum: Technical Articles
- Topic: Trailer bearing change
- Replies: 4
- Views: 2989
Re: Trailer bearing change
the repair