Search found 20 matches

by graham5494
Thu Feb 02, 2012 5:35 pm
Forum: General Discussion
Topic: Shafted
Replies: 10
Views: 6659

Re: Shafted

Thought I would check out my Mercury 3.5 long shaft. From cavitation plate to bracket top is 22 3/8 in around 570 mm . Hope this helps the database

graham5494
by graham5494
Sun Oct 30, 2011 5:47 pm
Forum: Investigators For Sale
Topic: Extra long Investigator on Trading post
Replies: 2
Views: 2774

Extra long Investigator on Trading post

Gidday all .

Spotted an extended Investigator on the Trading Post . Asking $14000 and 21 feet long. Might inspire some members to make theirs longer !

graham 5494
by graham5494
Thu Oct 13, 2011 3:13 pm
Forum: Technical Articles
Topic: Good Design Plate and Sail Number
Replies: 3
Views: 3111

Re: Good Design Plate and Sail Number

Gidday all .
My boat came with the Good Design plate supplied loose . Sure enough on the back of the plate is the number 90 which matches my sail number. Note that the number is a little rough , as in done by a hand engraver , not a stamp.

graham5494
by graham5494
Sat Aug 20, 2011 3:35 pm
Forum: Investigators For Sale
Topic: Investigator for sale Bracken Ridge Qld
Replies: 3
Views: 3202

Investigator for sale Bracken Ridge Qld

Gidday all . Went to see a local Investigator for sale. The boat is listed on http://www.boatsales.com.au (SSE-AD-245437) and is located in Bracken Ridge a northern suburb of Brisbane. The boat is a later model with the double hinged front hatch . It was based in Canberra and used in freshwater , wh...
by graham5494
Sun Mar 13, 2011 11:56 am
Forum: General Discussion
Topic: Another centre board removal question.
Replies: 8
Views: 5473

Re: Another centre board removal question.

Gidday all . Thinking on a bit.... be careful using aluminium in salt water if there is any chance of contact with stainless steel , remarkable corrosion can result ! Has anyone tried laminating a board using epoxy and glassfibre ? Perhaps alternating layers of chopped strand and unidirectional woul...
by graham5494
Fri Mar 11, 2011 7:04 pm
Forum: General Discussion
Topic: Another centre board removal question.
Replies: 8
Views: 5473

Re: Another centre board removal question.

Gidday all . I would recommend using stainless wire , not from a strength point of view , but because of abrasion resistance . The wire runs up a fairly narrow tube into the cabin , so swages need to be tight . One swage can be made on the bench but the lower one has to be done under the boat . Make...
by graham5494
Wed Mar 09, 2011 5:53 pm
Forum: General Discussion
Topic: Storage and use of space
Replies: 15
Views: 8354

Re: Storage and use of space

Gidday all . On this topic has anyone got a photo of a table installation ? Do I need to install a centre-board case to mount the table on ? Also where is the table stowed when not in use ?

graham5494
by graham5494
Wed Mar 09, 2011 5:47 pm
Forum: Investigators For Sale
Topic: Well Fitted out Investigator 563 in Queensland (Regents park
Replies: 1
Views: 4400

Re: Well Fitted out Investigator 563 in Queensland (Regents park

As far as I can see on Boatsales.com.au the advert is no longer there. Probably boat has been sold . Given its good condition this is not surprising !

graham 5494
by graham5494
Tue Feb 08, 2011 3:24 pm
Forum: General Discussion
Topic: Selling
Replies: 4
Views: 3501

Re: Selling

Gidday Benson . Sadly this year is proving to be one when it is extremely hard to sell any sailing boat . I have tried and failed over a number of months to sell mine . The Trading Post has listed two Investigators for a number of months with no movement . Ebay results in very low prices but only on...
by graham5494
Mon Jan 17, 2011 1:43 pm
Forum: Investigators For Sale
Topic: Investigator for sale
Replies: 1
Views: 2664

Investigator for sale

My Investigator sail number 90 is for sale .I urgently need $6500 for it to buy my next boat ! It has new paint , new main and nearly new outboard. If anyone is interested either ring or email me . email jacksongraham457 , phone 0466 964 717. Here are a few more details about the Investigator that I...